|
|
|
|
|
Release Number
|
Ballot Number/Title
|
Impact Statement
|
Approval
Date
|
Implementation
Date
|
|
80
|
208 and 209, Chapter 17, Interpretations
|
Ballot 208, is for adoption of no grace period for the requalification of hoisting and rigging activities. Once a person has exceeded the requalification window they must then start the training cycle over again, with either an initial training class or a challenge exam. An OJE for requalification beyond the 60 month window (36 month for forklift operators) is not allowed. Ballot 209 is to clarify that a Load Test does not need to meet the planning and documentation requirements of a Critical Lift Chapter 3.0 Critical Lifts.
|
September 8, 2016
|
|
|
79
|
Meeting Vote, Chapter 7, Shop Cranes
|
Meeting vote was held on March 17, 2016, to incorporate periodic inspection tag and load test tag into Chapter 7, Shop Cranes in the Hanford Site Hoisting and Rigging Manual.
|
April 27, 2016
|
|
|
79
|
207, Chapter 10, Rigging Hardware, Adoption of the current volume of ASME B30.26-2015
|
Ballot 207 is for the adoption of the current volume of ASME B30.26-2015, Rigging Hardware in the Hanford Site Hoisting & Rigging Manual. This adopts the requirement for shackle body and pin identification. The standard may incorporate more changes, but was determined to be editorial in nature and the Hanford site program already met or exceeds the change.
|
April 27, 2016
|
|
|
78
|
206, Chapter 3, Critical, Special, and Engineered Lifts, Chapter 14, Mobile Cranes, and Chapter 22, Appendix A, Definitions and Acronyms.
|
Ballot 206 is for adoption of the current volume of ASME B30.5-2014, Mobile & Locomotive Cranes in the Hanford Site Hoisting & Rigging Manual. This adoption adds guidance for multiple load line operation and outrigger lift-off. The definition of normal operating condition was revised. The changes may have some impact to Hanford as determined by the appointed Hoisting and Rigging reviewing subcommittee. The standard may incorporate more changes than listed, but they were determined to be editorial in nature or the current Hanford site program already met or exceeds the change.
|
January 4, 2016
|
|
|
78
|
205, Chapter 1, Introduction and Scope 1.2. Chapter 5, Hooks, Chapter 7, Shop Cranes, Chapter 9, Slings, Chapter 10, Rigging Hardware, Chapter 11, Below-The-Hook Lifting Devices, Chapter 12, Hoists, Jib Cranes, and Monorail Systems, Chapter 13, Overhead and Gantry Cranes, Chapter 14, Mobile Cranes, Chapter 15, Personnel Lifting, Chapter 16, A-Frames and Trolleys.
|
Ballot 205 is to update the Introduction of the Hanford Site Hoisting and Rigging Manual list of ASME B30 Standards. Chapter 1 will list all the years the ASME standards were issued and that they will be implemented as applicable. This ballot will also approve the ASME years to be removed from the body of the text in the Hanford Site Hoisting and Rigging Manual except where links to the ASME standard are addressed.
|
January 4, 2016
|
|
|
76
|
200, Hoisting and Rigging Training Program Description TPD-0016, Rev. 25
|
Ballot 200 is for revision #25 of the current TPD in Hanford Site Hoisting & Rigging Manual. The change is to add Load Charts and LMI Initial Training Course #042327 for Mobile Crane Inspection and Maintenance Personnel. The Hanford Site Hoisting & Rigging Manual Chapter 4, Personnel Qualifications and Training Requirements Appendix A(I) #19 addresses this requirement.
|
October 6, 2015
|
|
|
77
|
204, Chapter 2, Responsibilities and Chapter 4, Personnel Qualifications and Training Requirements.
|
Ballot 204 is for clarification of the training requirement that riggers need to complete prior to performing rigging operations with Mobile Equipment (forklifts, loaders, excavators, backhoes, etc). This ballot incorporates changes to TPD – 0016 Hoisting and Rigging. The ballot will take effect with an 8-month implementation period.
|
September 24, 2015
|
|
|
77
|
197B, clarification to Rigging Engineer training. 197A, Chapter 21, References & Bibliography, addresses reference standards.
|
Ballot 197B adds clarification to Rigging Engineer training to specifically identify Section 21.1 References. Ballot 197A is for the addition of a statement to Chapter 21 that addresses reference standards. Included in this ballot is adding into 21.1 References; BTH-1 Design of Below-the-Hook Lifting Devices, B30.21-Lever Hoists, B30.26 Rigging Hardware, and PASE-Portable Automotive Service Equipment. Also adding into 21.2 Bibliography, will be the addition of NQA-1 Quality Assurance Program Requirements for Nuclear Facilities.
|
September 24, 2015
|
|
|
76
|
203, Chapter 11, Below-the-Hook Lifting Devices, Adoption of the current volume of ASME BTH-1-2014
|
Ballot 203 is for the adoption of the current volume of ASME BTH-1-2014 Design of Below-the-Hook Lifting Devices in Chapter 11. The ASME BTH-1-2014 changes that may have some impact to Hanford, as determined by the appointed Hoisting & Rigging reviewing subcommittee, were determined to be editorial in nature or the current Hanford site program already met or exceeds the change.
|
September 2, 2015
|
|
|
76
|
202, Chapter 9, Slings, Adoption of the current volume of ASME B30.9-2014
|
Ballot 202 is for the adoption of the current volume of ASME B30.9-2014-Slings in Chapter 9. This edition contains extensive revisions including the use of the term LOAD HANDLING, recognizing the fact that the load could be moved vertically or horizontally. The load rated tables have been removed in this edition. This edition also addresses personnel competence and translations.
|
September 2, 2015
|
|
|
76
|
201, Chapter 7, Shop Cranes, update to current ASME standard for Portable Automotive Service Equipment (PASE-2014)
|
Ballot 201 is for revision of Chapter 7 to the current ASME standard Portable Automotive Lifting Devices (PALD). ASME committee changed the name and charter to Portable Automotive Service Equipment (PASE). The appointed Hoisting and Rigging reviewing subcommittee determined the changes were editorial in nature.
|
September 2, 2015
|
|
|
76
|
199, Chapter 3, Shop Cranes,3.3 Critical Lift Designation
|
Ballot 199, is for revision to Chapter 3, 3.3 Critical Lift Designation, item 5. The load being lifted is 90% or more of a mobile crane’s configured load chart rating.
|
September 2, 2015
|
|
|
75
|
196, Chapter 4, Personnel Qualifications and Training Requirements
|
Ballot 196 is to align the HSHRM with TPD-0016, Rev. 24. The change will remove ANSI as the only nationally accrediting certification agency for Crane Operators.
|
April 29, 2015
|
|
|
75
|
195, Global change to General Requirements
|
Ballot 195 is for a global change to the HSHRM. This will allow contractors to access ASME with more than one option. This statement is in general requirements section of chapters (5.2), (7.2), (9.2), (10.2), (11.2), (12.2), (13.2), (14.2), (15.2).
|
April 29, 2015
|
|
|
75
|
194, Chapter 5, Hooks, Adoption of the current volume of ASME B30.10-2014
|
Ballot 194 is for the adoption of the current volume of ASME B30.10-2014 HOOKS in the Hanford Site Hoisting & Rigging Manual (Chapter 5). The ASME B30.10-2014 changes that may have some impact to Hanford, as determined by the appointed Hoisting & Rigging reviewing subcommittee, were determined to be editorial in nature or the current Hanford site program already met or exceeds the change.
|
April 29, 2015
|
|
|
75
|
193, Chapter 11, Below-the-Hook Lifting Devices, Adoption of the current volume of ASME B30.20-2013
|
Ballot 193 is for the adoption of the current volume of ASME B30.20-2013 Below-the-Hook Lifting Devices in the Hanford Site Hoisting & Rigging Manual (Chapter 11). The ASME B30.20-2013 changes that may have some impact to Hanford, as determined by the appointed Hoisting & Rigging reviewing subcommittee, were determined to be editorial in nature or the current Hanford site program already met or exceeds the change.
|
April 29, 2015
|
|
|
75
|
192, Hoisting & Rigging Training Program Description TPD-0016, Rev. 24
|
Ballot 192 is for revision #24 of the current TPD in Hanford Site Hoisting & Rigging Manual. The change is to provide clarification for filing OJE forms, the removal of course #042870 Equipment Custodian Training requirement for an Assembly/Disassembly Director, added Certified Mobile Crane Operator requirements for spotter/signalman, removed NCCCO as the only nationally accrediting certification agency, added Appendix C: Hoisting and Rigging Site Forms list, and removed course #170661 Fire Extinguisher Training for Mobile/Cab Operated cranes.
|
April 29, 2015
|
|
|
75
|
187A, Chapter 4, Personnel Qualifications and Training Requirements, Rigging Engineer
|
Ballot 187A is for the addition of wording in Chapter 4, Personnel Qualification and Training Requirements of the HSHRM to define the training requirements for rigging engineers.
|
April 29, 2015
|
|
|
74
|
190, Chapter 6 Forklift Trucks
|
Ballot 190 is to change wording (cranes to forklift trucks) to the HSHRM Chapter 6.0 Forklift Trucks, 6.8.1 Operating Near Electric Power Lines.
|
November 10, 2014
|
|
|
74
|
189, Appendix B Users Guide
|
Ballot 189 is to adopt the 3RD Edition of the Riggers Reference Handbook as a user’s guide in the HSHRM. The Owner publisher has agreed to grant permission for us to post an electronic copy in the HSHRM as we have the ASME Standards. This will be a guide only and be precluded with a disclaimer that it does not replace or override requirements defined in the HSHRM.
|
November 10, 2014
|
|
|
74
|
188, Chapter 8 Wire Rope and Chapter 12 Hoists, Job Cranes, and Monorail Systems
|
Ballot 188 is to adopt current ASME B30 Standards B30.16-2012 and B30.21-2014. Chapter 8 Wire Rope was changed due to the revision of ASME B30.16 2012 and the requirement for wire rope replacement. We will give 20 days after vote approval to train the wire rope inspectors thru a Required Reading document. Chapter 12 Hoists, Jib Cranes, and Monorail Systems was updated to keep current with ASME B30.21-2014 Lever Hoists.
|
November 10, 2014
|
|
|
73
|
185-A-1, Chapter 1, Introduction
|
Ballot 185A-1 changes the wording in Chapter 1 Introduction, Section 1.2 Scope, of the Hanford Site Hoisting and Rigging Manual (HSHRM) to ensure activities being performed for the Department of Energy (DOE) are performed in a safe and cost effective manner. The HSHRM implements American Society of Mechanical Engineers (ASME) consensus and Occupation Safety and Health Administration (OSHA) standards to ensure the safety of hoisting and rigging operations to minimize risk to personnel and the public. Whether activities are performed by prime or subcontractors for the DOE, the same approved level of safety standards and requirements should be maintained.
|
April 30, 2014
|
|
|
72
|
184, Chapter 4, Personnel Qualifications and Training Requirements
|
Ballot 184 adds wire rope and fall protection to Chapter 4.0, Personnel Qualifications and Training Requirements, Appendix S, Assembly/Disassembly Director.
|
February 11, 2014
|
|
|
72
|
183, Chapter 1, Introduction
|
Ballot 183 updates ASME B30 standards not specifically addressed in the chapters of the HSHRM.
|
February 11, 2014
|
|
|
71
|
182, Attachment 1, Freight Container Lifting Standard
|
Ballot 182 adds guidance for handling freight containers in specific conditions not addressed in the standard and to provide for engineering analysis for non-standard handling configurations.
|
October 30, 2013
|
|
|
70
|
180, Chapter 14, Mobile Cranes, Crane Setback
|
Ballot 180 adds guidance to Chapter 14, Mobile Cranes, for mobile crane setup. The ballot proposes adding guidance for mobile crane setup when near slopes, excavations, shoring, and retaining walls and reduces the probability of crane instability due to loss of ground support.
|
July 18, 2013
|
|
|
69
|
179, Chapter 9, Slings, Identification
|
Ballot 179 changes Chapter 9, Slings, Identification. The ballot will require the three basic sling hitch capacities to be marked on slings.
|
March 28, 2013
|
|
|
70
|
178a, Chapter 6, Forklift Trucks
|
Ballot 178a changes Chapter 6, Forklift Trucks, Section 6.12, "Conduct of Operator," to provide guidance as to when a forklift operator should request the assistance of a spotter.
|
May 24, 2013
|
|
|
69
|
177, Attachment 2, Lifting Requirements for Concrete Blocks
|
Ballot 177 changes Attachment 2, Lifting Requirements for Concrete Blocks. This ballot changes the concrete block design requirements for lifting to allow equivalent design requirements to be used when approved by a qualified engineer.
|
March 27, 2013
|
|
|
68
|
176, Chapter 3, Critical Lifts, Lift Plan Approvals
|
Ballot 176 changes the title of Chapter 3, Critical Lifts, to Chapter 3, Critical, Special, and Engineered Lifts, to reflect chapter content and topics. This ballot also incorporates critical lift plan approval process and documentation retention to special and engineered lifts.
|
February 24, 2013
|
|
|
68
|
175, Chapter 5, Hooks, Temperature Limitations on Hooks
|
Ballot 175 brings forward existing wording from the applicable manufacturers and ASME standard addressing temperature limitations in Chapter 5, Hooks. THis ballot does not add or reduce existing requirements.
|
February 17, 2013
|
|
|
68
|
174, Chapter 9, Slings, Temperature Effects on Slings
|
Ballot 174 brings forward existing wording from the applicable manufacturers and ASME standard addressing temperature limitations in Chapter 9, Slings. THis ballot does not add or reduce existing requirements.
|
February 17, 2013
|
|
|
68
|
173, Chapter 10, Rigging Hardware, Temperature Limitations on Rigging Hardware
|
Ballot 173 brings forward existing wording from the applicable manufacturers and ASME standard addressing temperature limitations in Chapter 10, Rigging Hardware. THis ballot does not add or reduce existing requirements.
|
February 17, 2013
|
|
|
67
|
172, Chapter 4, Qualification and Training Requirements, Crane Operator Certification
|
Ballot 172 revises and updates wording in Chapter 4, Qualification and Training Requirements. This change brings the manual into compliance with OSHA 1926.1427, "Operator Qualification and Certification."
|
October 30, 2012
|
|
|
67
|
171, Chatper 20, Hanford Site Hoisting and Rigging Committee Charter
|
Ballot 171 revises and updates the wording in the Hanford Site Hoisting and Rigging Committe Charter. The change strengthens the participation in ASME Committees and better defines the description of the ASME standards that are applicable to the chairman's participation.
|
October 30, 2012
|
|
|
|
169, Chapter 9, Slings, D/d Ratio
|
Ballot 169 approves adding the D/d ratio chart to Chapter 9, Slings, now that the chart is no longer published in ASME B30.9, as well as adding language to clarify the application of the D/d ratio.
|
August 23, 2012
|
|
|
|
168, Chapter 1, Scope
|
Ballot 168 approves the update to Chapter 1, Scope. This ballot will update the list of ASME B30 standards not addressed in specific chapters of the Hanford Site Hoisting & Rigging Manual as well as directing attention to the application of OSHA 1926 requirements and addressing rigging equipment that is used in an application than the application for which it was manufactured.
|
August 23, 2012
|
|
|
|
167, Chapter 4, Qualification and Training Requirements, BTH Training
|
Ballot 167 approves the addition of wording in Chapter 4, Qualification and Training Requirements, addressing training elements in ASME B30.20 for personnel using below-the-hook lifting devices.
|
August 16, 2012
|
|
|
|
166, Chapter 4,Qualification and Training Requirements, Documentation of On-the-Job Training
|
Ballot 166 approves the addition of wording in Chapter 4, Qualification and Training Requirements, requiring documentation of completion, or bypassing, of on-the-job training that is currently in Chapter 4.
|
August 16, 2012
|
September 25, 2012
|
|
|
165, Adoption of the Current Volume of ASME B30.23-2011
|
Ballot 165 adopts the current volume of ASME B30.23-2011, Personnel Lifting Systems, in the Hanford Site Hoisting & Rigging Manual.
|
July 16, 2012
|
August 15, 2012
|
|
|
164, Adoption of the Current Volume of ASME B30.5-2011
|
Ballot 164 adopts the current volume of ASME B30.5-2011, Mobile & Locomotive Cranes, in the Hanford Site Hoisting & Rigging Manual.
|
July 16, 2012
|
August 15, 2012
|
|
|
163, Adoption of the Current Volume of ASME B30.11-2011
|
Ballot 163 adopts the current volume of ASME B30.11-2010, Monorails and Underhung Cranes, in the Hanford Site Hoisting & Rigging Manual.
|
July 16, 2012
|
August 15, 2012
|
|
|
162, Adoption of the Current Volume of ASME B30.2-2011
|
Ballot 162 adopts the current volume of ASME B30.2-2011, Overhead and Gantry Cranes, in the Hanford Site Hoisting & Rigging Manual.
|
July 16, 2012
|
August 15, 2012
|
|
|
161, Attachments Chapter: Freight Container Lifting Standard
|
Ballot 161 added criteria in Attachment 1, Freight Container Lifting Standard, to address movement of freight containers without fork pockets, with a forklift, when residing/stored in the prohibited zone as defined in DOE-0359, Hanford Site Electrical Safety Program.
|
May 1, 2012
|
May 10, 2012
|
|
|
160, Scope
|
Ballot 160 clarified wording in Chapter 1, Introduction, Section 1.2, Scope, of the Hanford Site Hoisting and Rigging Manual (HSHRM) to ensure activities being performed for the Department of Energy (DOE) are performed in a safe and cost-effective manner. The HSHRM implements American Society of Mechanical Engineers (ASME) consensus and Occupations Safety and Health Administration (OSHA) standards to ensure the safety of hoisting and rigging operations to minimize risk to personnel and the public. Whether activities are performed by prime or subcontractors for DOE, on-site or off, the same approved level of safety standard and requirements should be maintained.
|
May 1, 2012
|
May 10, 2012
|
|
|
159, Adoption of a User Guide Chapter
|
Ballot 159 adopts the Riggers Reference Handbook as a user's guide chapter in the Hanford Site Hoisting Rigging Manual (HSHRM). The Owner/Publisher has agreed to grant permission to post an electronic copy in the HSHRM, similar to the process with the American Society of Mechanical Engineers (ASME) standards. This will be a guide only and be precluded with a disclaimer that it does not replace or override requirements defined in the HSHRM.
|
April 26, 2012
|
|
|
|
158, Termination of Controlled Hard Copies of the HSHRM
|
Ballot 158 approved the termination of the production of controlled hard copies of the Hanford Site Hoisting & Rigging Manual (HSHRM). The HSHRM is available on the intranet and internet and can be downloaded and printed for those who wish to maintain a hard copy. This change will allow the immediate publication of approved ballots rather than the current practice of waiting several months to gather ballots to perform a controlled hard copy release. The change will result in a cost savings and ensure each ballot is published upon approval on the intranet and internet, reducing the current lag time between approval and publication of the change.
|
April 12, 2012
|
April 12, 2012 |
|
|
Last Updated 11/08/2022 11:38 AM
|
|
°F
